下扬子地区下志留统风暴沉积特征及风暴作用对泥页岩品质的影响

近年来在下扬子地区页岩气地质调查井所获取的地层岩心资料，揭示该地区下志留统风暴沉积较为发育。基于精细的岩心观察描述，详细分析了下扬子地区下志留统高家边组下段中上部风暴沉积的特征，并阐明了风暴作用对泥页岩的影响。研究表明：研究区风暴岩岩性偏细，以粉砂岩为主，石英含量较高，结构成熟度较低，具2种不同的粒度概率曲线；主要发育底部冲刷面、块状层理、平行层理、丘状交错层理、波纹交错层理、准同生变形构造等沉积构造；垂向上主要识别出4种风暴沉积序列，均具有从底到顶粒度变细的沉积特征，不同的沉积序列与风暴流能量的强弱有关。下扬子地区早志留世频繁的风暴活动与研究区的古地理背景和古气候条件具有内在联系。特大型风暴对浅海陆棚深水区的细粒泥质沉积物特征产生重要影响，包括降低有机质含量、减少单层厚度、破坏垂向连续性、改变原始沉积构造和侧向稳定性等，总体上降低了泥页岩的品质。因此，研究认为在页岩气的勘探和评价过程中应重视风暴因素对陆棚深水区原始泥质沉积物的影响。     

The formed surface characteristics of SiCf/SiC composite in the nanosecond pulsed laser ablation

For the advantages of high-temperature resistance, corrosion resistance and ultra-high hardness, SiC_f/SiC composite is becoming a preferred material for manufacturing aero-engine parts. However, the anisotropy and heterogeneity bring great challenges to the processing technology. In this study, a nanosecond pulsed laser is applied to process SiC_f/SiC composite, where the influence of the scanning speed and laser scanning direction to the SiC fibers on the morphology of ablated grooves is investigated. The surface characteristics after ablation and the involved chemical reaction of SiC_f/SiC are explored. The results show that the increased laser scanning speed, accompanied by the decreasing spot overlap rate, leads to the less accumulation of energy on the material surface, so the ablation effect drops. In addition, for the anisotropy of the SiC_f/SiC material, the obtained surface characteristics are closely dependent on the laser scanning direction to the SiC fibers, resulting in different groove morphology. The element composition and phase analysis of the machined surface indicate that the main deposited product is SiO₂ and the carbon substance. The results can provide preliminary technical support for controlling the machining quality of ceramic matrix composites.     

Laser damage resistance of plasma-sprayed alumina and honeycomb skeleton/alumina composite ceramic coatings

Al₂O₃ and honeycomb skeleton-Al₂O₃ composite coatings on Titanium alloy (Ti–6Al–4V) were prepared by atmospheric plasma spraying. A laser ablation experiment on as-sprayed coatings was performed. In this paper, the laser damage resistance, microstructure, phase composition of Al₂O₃ coatings were examined. 3D Dimensional Confocal Microscopy, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and Energy Dispersive Spectrometry (EDS) characterized the laser damage morphology, microstructure, phase composition, and element analysis, respectively. The influence of the honeycomb skeleton on the laser ablation damage on as-sprayed coatings was investigated by a comparative analysis of the laser damage morphology with different laser ablation times and gas flow. The results show that the honeycomb skeleton raises thermal conductivity and thermal diffusivity. Moreover, a “tower”-like dendrite was generated during the laser irradiation of the composite coating. The honeycomb skeleton refined the structure, suppressed crack propagation, and reduced the influence of gas flow on cracks. Under the same experimental laser ablation parameters, the laser damage area of the honeycomb skeleton-Al₂O₃ composite coating was smaller than that of the Al₂O₃ coating. It was demonstrated that the laser damage resistance of the honeycomb skeleton-Al₂O₃ composite coating was superior to that of the Al₂O₃ coating.     

Enhancement of oxygen/pressure sensing performance of Eu3+-doped YSZ phosphors via Bi3+ sensitization

The effects of the incorporation of a Bi³⁺ sensitizer on the phosphorescence properties and oxygen partial pressure sensitivity of the Eu³⁺ doped yttria stabilized zirconia (YSZ) phosphors were studied using a lifetime-based optical measurement system. Two series of YSZ: Eu phosphors were investigated in this work: Eu_0.01Bi_xY_0.07-xZr_0.92O_1.96 substitutional series and Eu_0.01Bi_xY_0.07Zr_0.92-xO_1.96-0.5x additive series. The phosphorescence intensity of the additive-series phosphors was enhanced by 47% excited at 405 nm with a Bi³⁺ concentration of 2 mol% due to the energy transfer between Bi³⁺ and Eu³⁺. In contrast, the phosphorescence intensity of the substitutional-series phosphors decreased as the Bi³⁺ concentration increased. The phosphorescence lifetimes for both series phosphors were highly sensitive to oxygen partial pressure at elevated temperatures. With increasing Bi³⁺ concentration, the oxygen sensitivities of both series were enhanced initially, which was related to the increment of concentration dependent non-radiative decay via cross-relaxation between Bi³⁺ and Eu³⁺. With 1 mol% Bi³⁺ doping, the oxygen sensitivity was enhanced by 28% and 12% for substitutional-series and additive-series phosphors, respectively. As the Bi³⁺ concentration further increased, the oxygen sensitivities of both series declined, which was attributed to the energy transfer between Bi³⁺, the formation of Bi³⁺ aggregates as well as the increase of the Eu³⁺ site symmetry. The results of this study not only provided valuable references for phosphor thermometry, but also offered new ideas for developing high-temperature non-contact pressure sensors.     

Comparison of ignition,injection and micro - Explosion characteristics of RP-3/ ethanol and biodiesel / ethanol mixed drops

The ignition, injection, and micro-explosion characteristics of aviation fuel (RP-3)/ethanol mixed droplets and biodiesel/ethanol mixed droplets at different proportions under high temperature conditions (420 °C) were compared using an experimental setup. A device for measuring small droplet volumes was designed using an infusion set and different types of needles, and a corresponding equation was established. Mixed droplets suspended on high-temperature resistance nichrome wire with a diameter of 0.2 mm were heated by sending them to a position approximately 2 mm from the forklift preheating plug using a moving rail. SLR and high-speed cameras were used to observe the flame structure as well as the injection and micro-explosion of the mixed droplets during combustion, respectively. Expansion, injection, and micro-explosion were observed in the biodiesel/ethanol mixed droplet experiments when the biodiesel content was 60%. Although the micro-explosion of mixed droplets of aviation fuel/ethanol was not observed, expansion and ejection of the droplets were observed. Image Pro-plus software was used to calculate the diameters at different times in the combustion cycle of the droplets. Through this analysis, the occurrence of micro-explosion was described, and a model for the calculation of micro-explosion strength was established.     

面向云计算应用层演化的隐私保护方法研究

云计算应用层中的组合服务具有演化属性,因此,隐私数据在服务组合过程中,用户的隐私数据可能会因为服务或服务流程的演化而暴露。根据服务演化的特征,以描述逻辑为基础,提出了一种面向云计算应用层演化的隐私保护方法。对隐私协议进行形式化描述;根据服务的演化特征,对服务的演化进行监控,保证满足用户的隐私需求;利用实例研究证明该方法的正确性与可行性。     

Highly efficient chemical mechanical polishing method for SiC substrates using enhanced slurry containing bubbles of ozone gas

In this study, a highly efficient method for chemical mechanical polishing (CMP) of silicon carbide (SiC) substrates using enhanced slurry was proposed and developed. The enhanced slurry contains bubbles of ozone gas generated by ozone gas generator in pure water mixed with a conventional commercially available slurry. Therefore, the enhanced slurry has an oxidizing effect on the Si-face of SiC substrates. To confirm the effectiveness of bubbles enclosing ozone gas, both nano-indentation test and X-ray photoelectron spectroscopy (XPS) analysis were conducted. As a result, the hardness decrease of the Si-face of the SiC substrate was confirmed through the nano-indentation test, and the generation of reaction products was confirmed on Si-face of SiC substrate in the XPS analysis. According to a series of experimental results of our proposed highly efficient CMP method for SiC substrates, the removal rate can be increased when the enhanced slurry was applied, comparing with that for the not only conventional commercially available slurry but also commercially available dedicated slurry.     

预压力对压电驱动履带移动系统的性能影响

为了提高夹心式压电驱动移动系统的机械输出性能，提出了一种U型预压力调节机构，并开展了预压力对夹心式压电驱动履带移动系统输出性能影响关系的实验研究。首先，针对U型预压力调节机构的安装对夹心式压电振子的振动特性影响关系开展了有限元仿真分析，发现U型预压力调节机构始终处在夹心式压电振子的两相工作模态振动节点位置；其次，开展了夹心式压电驱动履带移动系统的原理样机的预压力调节测试实验，确定了系统的最大输出牵引力及其所对应的最佳预压力；最后，在最佳预压力工作状态下，开展了原理样机的牵引力特性、越障性能以及模拟月壤环境下的运动特性实验。研究结果表明，在最佳预压力工作状态下，夹心式压电驱动履带移动系统的机械输出性能最佳，为其进一步在月面巡视器上的应用提供了技术支持和试验基础。     

桁架式火星探测器的着陆缓冲特性分析

着陆缓冲机构是着陆器实现行星探测软着陆的关键部位之一,它的缓冲性能直接关系到着陆器是否能安全地在行星表面实现软着陆。根据某院提供的火星着陆器模型,在三维建模软件中建立着陆器的合理简化模型,为了提高分析着陆器软着陆过程冲击响应的准确性,采用MSC公司的Patran/Dytran有限元软件,用瞬态动力学的方法对着陆器的缓冲性能进行分析。仿真结果与试验数据十分吻合,着陆器的缓冲和传力性能良好。因此,采用拉杆缓冲的桁架式火星着陆器是可行的,仿真结果与试验数据也为今后的火星探测提供了参考。     

正偏心正交车铣精加工切削层几何形状研究

针对未考虑正偏心正交车铣切削层几何形状而导致难以全面反映正交车铣切削层几何形状变化规律的问题，基于正交车铣运动规律，在不考虑动力学影响的情况下，对切削层的形成过程进行了静态分析。建立的正偏心正交车铣切削层几何形状的解析模型涉及铣刀侧刃和底刃的切入/切出角度、切削厚度和切削深度。通过试验验证了该解析模型的正确性，并分析了切削参数对铣刀切削层的影响。研究结果为正偏心正交车铣切削层几何形状的变化提供了定量的分析依据，为切削力和颤振的研究提供了理论指导。